![background image](http://html1.mh-extra.com/html/eaton/cutler-hammer-fp-6000-series/cutler-hammer-fp-6000-series_instructions-manual_4035779196.webp)
Instructional Literature
Page
196
Effective: May 2008
Instructions for the FP-6000 Protective Relay
For more information visit: www.eaton.com
IB02602004E
Any contact input state change can be logged in the Event log if
so programmed. Each input can be logged or not logged
according to the program settings (see Section 5). The value
given for each event is: Active for an input transition of low to
high, or inactive for an input transition of high to low. Table 63
summarizes the contact input causes for an event log.
Table 63. Event Input Cause Table.
All contact output changes will be logged in the event log and no
programming is necessary. If more than one relay changes state
at exactly the same time because of a single causal event
activating more than one relay, only one log is entered into the
event log. Table 64 summarizes all output event causes that will
be logged.
Table 64. Event Output Cause Table.
Breaker commands that come through the FP-6000, breaker state
changes and breaker alarms are all logged automatically in the
event log. Table 65 shows all possible causes for breaker event
logs.
Table 65. Event Breaker Cause Table.
CAUSE
CAUSE DESCRIPTION
VALUE GIVEN
Cin1State Alt
Contact Input 1 State changed
Active or Inactive
Cin2State Alt
Contact Input 2 State changed
Active or Inactive
Cin3State Alt
Contact Input 3 State changed
Active or Inactive
Cin4State Alt
Contact Input 4 State changed
Active or Inactive
Cin5State Alt
Contact Input 5 State changed
Active or Inactive
Cin6State Alt
Contact Input 6 State changed
Active or Inactive
Cin7State Alt
Contact Input 7 State changed
Active or Inactive
Cin8State Alt
Contact Input 8 State changed
Active or Inactive
CAUSE
CAUSE DESCRIPTION
VALUE GIVEN
Relay Changed
One of the first 6 relays – Trip 1, Trip 2, Rly3, Rly4, Rly5, or Alarm
– has changed state.
Output Status – contains the status flag for all contact outputs.
Healthy State
The Relay Healthy contact output has changed state.
Output Status – contains the status flag for all contact outputs.
CAUSE
CAUSE DESCRIPTION
VALUE GIVEN
Open Breaker
An Open Breaker command is given remotely or through the
front panel pushbutton.
Breaker Status – contains all the flags related to the breaker.
Close Breaker
A Close Breaker command is given remotely or through the
front panel pushbutton.
Breaker Status – contains all the flags related to the breaker.
Bkr Opened
The Breaker State is determined to be Opened.
Breaker Status – contains all the flags related to the breaker.
Bkr Closed
The Breaker State is determined to be Closed.
Breaker Status – contains all the flags related to the breaker.
Bkr Lockout
The Breaker has failed to break the current in the programmed
amount of time.
Breaker Status – contains all the flags related to the breaker.
Slow Bkr Alm
The Breaker has taken more than 40 cycles in the programmed
amount of time.
Breaker Status – contains all the flags related to the breaker.
Bkr State Alm
There is a state disagreement between the 52A and 52B con-
tact inputs.
Breaker Status – contains all the flags related to the breaker.
Trip1 Mntr Alm
The Breaker is determined to be in the closed state and no
trickle open (trip) coil current is sensed around the Trip 1 con-
tact output.
Breaker Status – contains all the flags related to the breaker.
Trip2 Mntr Alm
The Breaker is determined to be in the open state and no
trickle close coil current is sensed around the Trip 2 contact
output.
Breaker Status – contains all the flags related to the breaker.
AR Close
Autoreclose closing request.
Breaker State Flags.
AR Lockout
Autoreclose logic enters Lockout mode.
CNTL Autoreclose Lockout Flags.
AR Anti-pump
Autoreclose logic enters anti-pumping process.
CNTL Autoreclose Operation Flags.
BkrWearAlm
Breaker exceeds its wear alarm limit.
Breaker State Flags.