manualshive.com logo in svg

Dell S4048-ON, Руководство по настройке

Поделиться
Скачать
Dell S4048-ON Скачать руководство пользователя страница 448

neighbor within its LSPs. The local router does not form an adjacency if both routers do not have at least one common MT over the 
interface.

Graceful Restart

Graceful restart is a protocol-based mechanism that preserves the forwarding table of the restarting router and its neighbors for a 
specified period to minimize the loss of packets. A graceful-restart router does not immediately assume that a neighbor is 
permanently down and so does not trigger a topology change.

Normally, when an IS-IS router is restarted, temporary disruption of routing occurs due to events in both the restarting router and 
the neighbors of the restarting router. When a router goes down without a graceful restart, there is a potential to lose access to 
parts of the network due to the necessity of network topology changes.

IS-IS graceful restart recognizes that in a modern router, the control plane and data plane are functionally separate. Restarting the 
control plane functionality (such as the failover of the active route processor module (RPM) to the backup in a redundant 
configuration) should not necessarily interrupt data packet forwarding. This behavior is supported because the forwarding tables 
previously computed by an active RPM have been downloaded into the forwarding information base (FIB) on the line cards (the data 
plane). For packets that have existing FIB/content addressable memory (CAM) entries, forwarding between ingress and egress ports 
can continue uninterrupted while the control plane IS-IS process comes back to full functionality and rebuilds its routing tables.

A new TLV (the Restart TLV) is introduced in the IIH PDUs, indicating that the router supports graceful restart.

Timers

Three timers are used to support IS-IS graceful restart functionality. After you enable graceful restart, these timers manage the 
graceful restart process.

There are three times, T1, T2, and T3.

•

The T1 timer specifies the wait time before unacknowledged restart requests are generated. This is the interval before the 

system sends a Restart Request (an IIH with the RR bit set in Restart TLV) until the complete sequence number PDU (CSNP) is 

received from the helping router. You can set the duration to a specific amount of time (seconds) or a number of attempts.

•

The T2 timer is the maximum time that the system waits for LSP database synchronization. This timer applies to the database 

type (level-1, level-2, or both).

•

The T3 timer sets the overall wait time after which the router determines that it has failed to achieve database synchronization 

(by setting the overload bit in its own LSP). You can base this timer on adjacency settings with the value derived from adjacent 

routers that are engaged in graceful restart recovery (the minimum of all the Remaining Time values advertised by the neighbors) 

or by setting a specific amount of time manually.

Implementation Information

IS-IS implementation supports one instance of IS-IS and six areas.

You can configure the system as a Level 1 router, a Level 2 router, or a Level 1-2 router. For IPv6, the IPv4 implementation has been 
expanded to include two new type, length, values (TLVs) in the PDU that carry information required for IPv6 routing. The new TLVs 
are 

IPv6 Reachability

 and 

IPv6 Interface Address

. Also, a new IPv6 protocol identifier has also been included in the supported TLVs. 

The new TLVs use the extended metrics and up/down bit semantics.
Multi-topology IS-IS adds TLVs:

•

MT TLV

 — contains one or more Multi-Topology IDs in which the router participates. This TLV is included in IIH and the first

 

fragment of an LSP.

•

MT Intermediate Systems TLV

 — appears for every topology a node supports. An MT ID is added to the extended IS 

reachability TLV type 22.

•

MT Reachable IPv4 Prefixes TLV

 — appears for each IPv4 an IS announces for a given MT ID. Its structure is aligned with the 

extended IS Reachability TLV Type 236 and it adds an MT ID.

•

MT Reachable IPv6 Prefixes TLV

 — appears for each IPv6 an IS announces for a given MT ID. Its structure is aligned with the 

extended IS Reachability TLV Type 236 and add an MT ID.

448

Intermediate System to Intermediate System

Содержание S4048-ON
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды