
10.68.160.1
10.68.161.1
10.68.162.1
10.68.163.1
10.68.164.1
10.68.165.1
10.68.166.1
10.68.167.1
10.68.168.1
10.68.169.1
10.68.170.1
10.68.171.1
10.68.172.1
10.68.173.1
10.68.174.1
10.68.175.1
10.68.176.1
10.68.177.1
10.68.178.1
10.68.179.1
10.68.180.1
10.68.181.1
10.68.182.1
10.68.183.1
10.68.184.1
10.68.185.1
Dell>
Configuring BGP Fast Fall-Over
By default, a BGP session is governed by the hold time.
BGP routers typically carry large routing tables, so frequent session resets are not desirable. The BGP fast fall-over feature reduces
the convergence time while maintaining stability. The connection to a BGP peer is immediately reset if a link to a directly connected
external peer fails.
When you enable fall-over, BGP tracks IP reachability to the peer remote address and the peer local address. Whenever either
address becomes unreachable (for example, no active route exists in the routing table for peer IPv6 destinations/local address), BGP
brings down the session with the peer.
The BGP fast fall-over feature is configured on a per-neighbor or peer-group basis and is disabled by default.
To enable the BGP fast fall-over feature, use the following command.
To disable fast fall-over, use the
[no] neighbor [neighbor | peer-group] fall-over
command in CONFIGURATION
ROUTER BGP mode.
•
Enable BGP Fast fall-Over.
CONFIG-ROUTER-BGP mode
neighbor {
ip-address
|
peer-group-name
} fall-over
Examples of Verifying that Fast fall-Over is Enabled on a BGP Neighbor and a Peer-Group
To verify that you enabled fast fall-over on a particular BGP neighbor, use the
show ip bgp neighbors
command. Because
fast fall-over is disabled by default, it appears only if it has been enabled (shown in bold).
Dell#sh ip bgp neighbors
BGP neighbor is 100.100.100.100, remote AS 65517, internal link
Member of peer-group test for session parameters
BGP version 4, remote router ID 30.30.30.5
BGP state ESTABLISHED, in this state for 00:19:15
Last read 00:00:15, last write 00:00:06
Hold time is 180, keepalive interval is 60 seconds
Received 52 messages, 0 notifications, 0 in queue
Sent 45 messages, 5 notifications, 0 in queue
192
Border Gateway Protocol IPv4 (BGPv4)
Содержание S4048-ON
