Daikin D-BACS, Руководство по конструкции

Страница: 320 / 376

1.5 Dio Unit (DEC102A51) 303
Adaptor
The figure below shows the printed circuit board built in this equipment.
H4P
H12P
3
ON
7 2 6 8 5 1 4
3 2 1 8 4 7 6 5
ON
1 4 2 3
ON
DS6
DS2 DS3
DS4 DS5
Contactor
SS1
Con. Ins.
Group No. Set
DS1 High
0
RS1 Low
D2 CD D3 D1 D4
CA A4
M1
A3
CM
A2 A1
M4 M3 M2
F2
F1
N
L
INPUT
H1P H2P
Operation
Monitor
(GRN)
H3P
H10P
4 1 2
H9P
Aiarm
Monitor
(RED)
H11P
3
X1M
X2M
X3M
TNc2
HAP
TNa1
HAP
TNb4
RED
TNc1
TNa3
TNc4
GRN
TNc3
X1A
YE
TNb3
LED10
H10P
TNa4
RED
AC200V
~240V
TNb1
TP1
TNa2
X4M
TNb2
X2A
Terminal block for transmission
(F1/F2) (Terminal size: M3)
Connect this unit to the terminals F1, F2
of the centralized control equipment.
When the transmission is
abnormal, the lamp lights up,
disabling remote control.
(The lamp goes out in the
normal condition.)
The start / stop signal is outputted
to the equipment to be connected.
Abnormal output cutoff / hold
switch (DS5)
This switch makes it possible to select
continuous 1 output or instantaneous 2 output.
Forced stop switch (DS6-4)
Switch for selecting the number
of facility equipment connected
(DS3)
It is possible to select whether
the equipment connection error
is a non-latch or latch error.
Set the switch according to the number
of facility equipment connections.
Shortcircuit during control
quantity setting
Transmission error monitor
(LED10: Red)
DIII-NET Address No. setting
switch (RS1/DS1)
This switch makes it possible to
select whether the system should
be reset to the state before power
failure or not when the power
failure was recovered.
Monitor input switch
(DS6-3)
Output selector switch (SS1)
Start / Stop error switch (DS4-4)
When the microcomputer is in
normal operation, the lamp flickers.
This switch makes it possible to
select whether the operation
output is interrupted or held
when an abnormality occurred
in the connected equipment.
Whether or not the abnormal condition
of facility equipment during stop is
recognized can be selected.
Transmission error switch (DS4-2)
Later push priority switch (DS4-3)
The facility equipment status
is monitored.
Set DIII-NET Address No.
Whether the connected equipment
"error" is detected with contact input
"Open" or "Closed" can be selected.
Terminal block for monitor
input (Terminal size: M3.5)
Terminal block for control
output (Terminal size: M3.5)
This switch makes it possible to
select whether the forced stop
signal should be followed or
neglected.
Switching of whether or not error
detection for start / stop operation
from i-Manager is done is performed.
Start error masks witch
(DS6-1)
This switch makes it possible to
select the absence or presence
of later push priority switch.
Power supply terminal
block (L, N)
For the power supply,
use 1 ~ 200 - 240V.
Quantity change shortcircuit
pin (TP1)
The power transformer
connector is connected.
Momentary stop auto switch (DS4-1)
This switch makes it possible to
select whether the control output
state is maintained or not when
the transmission is abnormal.
Abnormal input detecting switch
(DS2)
Error detecting switch
(DS6-2)
Transformer connecting
connector (CN1/CN2)
Microcomputer OK monitor
(LED-A: Green)
It is possible to select whether
the error at startup is masked
for 10 or 30 seconds.