Consilium Salwico CS3000 Скачать руководство пользователя страница 80

Страница: 80 / 83

Document no.:

S-4-007.875/E

Prepared: 2002-10-01

Revision:

R5 2004-04-07 BM

2002, Consilium Marine AB

Service manual

Appendix C: Fault codes C-12

CS3000

174

NO POWER SUPPLY FOR LOOP

Cause

Remedy

No power feed from the pcb.

DC/DC converter faulty.

175

DOOR IN WRONG POSITION

Cause

Remedy

Door in wrong position.

Check for obstruction.

176

CABLE BREAK POSITIVE SIDE

Cause

Remedy

Check for a cable break on positive lead.

Mend the cable break.

A tripped short circuit isolator can cause
this fault.

Check the short circuit isolators.

177

CABLE BREAK NEGATIVE SIDE

Cause

Remedy

Check for a cable break on negative lead.

Mend the cable break.

A tripped short circuit isolator can cause
this fault.

Check the short circuit isolators.

178

WRONG TYPE OF LOOP UNIT FOUND

Cause

Remedy

Check the ID setting of the faulty unit.

Set a correct value on the DIP-
switch of the unit.

179

UNABLE TO DETECT SHORT CIRCUIT

Cause

Remedy

Unable to detect short circuit.

Exchange loop-PCB.

180

SPRINKLER VALVE CLOSED

Cause

Remedy

Sprinkler valve closed.

Check why it is closed.

Содержание Salwico CS3000




















































































Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды

Consilium Salwico CS3000, Руководство по обслуживанию

Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды