manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 28

Service manual CS3000 

Chapter 3: Input board  INK-2 3-19 

The circuit boards of the central unit 

 

 

Document no.: 

S-4-007.875/E 

Prepared: 

1995-03-17  Fia 

Revision: 

R4  2004-03-15  BM 

 
© 2002, Consilium Marine AB  

 

Input board INK-2  

General 

The input board INK-2 is used for getting information about external activities, 
which can be used, for example, to control other outputs. The INK-2 board is 
controlled by the alarm processor board LPK-2, via the address and data buses 
in the back plane. The board also contains a status register for functional 
checks. 

The INK-2 board is equipped with 24 opto-isolated inputs for 24 VDC/10 mA. 
These inputs are divided into six groups, each with four inputs with a common 
return conductor. 

Handling 

 

Indications 

There are two LEDs on the front panel of the board.  

 

No 1 (green) when lit: proper voltage supply. 

No 2 (green) when lit: the board is properly polled. 

Fuse 

The battery voltage is fused. If the fuse is blown a signal is activated in the 
back plane. The fuse is accessible on the front panel of the board, and can be 
used for disconnecting the power. 

Fuse rating: 250 mAT  5x20 mm 

Setting the address 

The address of the board is set with a DIP-switch (SW1), with 8 switches. The 
address bits #2 - #9 are set. Bit #2 is set with SW1-1, and bit #9 with SW1-8. 
For more information see Appendix A. 

Restarting the board 

Remove the fuse from the board to disconnect the power. When the fuse is put 
back on, the board is restarted. 

Replacing the board 

To replace INK-2 follow these steps: 

1.

 

Shut down the central by removing the fuses F3-F6 on the KE-2 rectifier. 

 

WARNING!

  

The power must be disconnected before the board is removed. 

2.

 

Remove the board and replace it with the new board. 

3.

 

Start up the central by inserting F3+F4 and F5+F6 in that order. 

1

2

Salwico INK-2

 

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды