manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 5

Service Manual CS3000 

Chapter 1: Service mode   1-1    

Control unit 
 
 

Document no.: 

S-4-007.875/E 

Prepared: 

1995-03-17  Fia 

Revision: 

R4  2004-03-15 BM 

 
© 1995, Consilium Marine AB  

Chapter 1: Control unit 

Service mode 

The control unit includes a fourth access level to be used only by the service 
engineer. There are two functions in the service mode: bypass the built-in short 
circuit isolators and definition of control unit address.  

Set address 

(Access level 4) 

Each control unit in the system must have a unique address in the interval 217 
- 232. The control unit number must correspond with the number defined in 
the Definition program. The control unit address must be set after the system 
definition is downloaded and the system is restarted. 

•

 

Press F4 (MENU) until SERVICE is displayed on line 4. 

•

 

Press F1 (SERVICE). 

•

 

Press F1 (ADDRESS). 

•

 

Enter the address for the control unit. The address interval is 217 - 232.  

Bypass built-in short circuit isolators 

The built-in short circuit isolators, two on each loop, are bypassed when you 
activate the SERVICE function. The short circuit isolators remain bypassed 
until you activate them again.  

•

 

Press F4 (MENU) until SERVICE is displayed on line 4. 

•

 

Press F1 (SERVICE). 

 

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды