Consilium Salwico CS3000 Скачать руководство пользователя страница 70

Страница: 70 / 83

Document no.:

S-4-007.875/E

Prepared: 2002-10-01

Revision:

R5 2004-04-07 BM

2002, Consilium Marine AB

Service manual

Appendix C: Fault codes C-2

CS3000

4 ADDITIONAL

CENTRAL

The central unit found an additional sub-central unit after cold start.

Cause

Remedy

Wrong definition of number of central
units.

Check the specification and
redefine the system.

5 LOOP(S)

MISSING

The main central unit is missing a loop after cold start.

Cause

Remedy

SPK-2 or LPK-2 has a hardware fault.

Exchange the board.

Wrong definition of number of loops.

Check the specification and
redefine the system.

6 ADDITIONAL

LOOP(S)

The central unit found an additional loop after cold start.

Cause

Remedy

Wrong definition of number of loops.

Check the specification and
redefine the system.

MISSING LOOP UNIT

Fewer loop units have been found than defined in the loop.

Cause

Remedy

Wrong definition of number of loop units.

Check the specification and
redefine the system.

Loop unit connections faulty.

Connect the unit correctly

Missing answer from a loop unit.

Exchange the unit.

ADDITIONAL LOOP UNIT(S)

More loop units have been found than defined in the loop.

Cause

Remedy

Wrong definition of number of loop units.

Check the specification and
redefine the system.

Loop unit connections faulty.

Connect the unit correctly.

LOOP MISSING DEF. DATA

Cause

Remedy

The loop has not been defined properly at
the installation.

Redefine the loop.

Содержание Salwico CS3000




















































































Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды

Consilium Salwico CS3000, Руководство по обслуживанию

Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды