Consilium Salwico CS3000 Скачать руководство пользователя страница 8

Страница: 8 / 83

Service Manual CS3000

Chapter 2: Input/Output board IKK-4

2-3

The circuit board of the control unit

Document no.:

S-4-007.875/E

Prepared:

1995-03-17 Fia

Revision:

R4 2004-03-15 BM

1. Data buffer

The data bus is buffered before entering/leaving the board.

2. Address decoder

The address decoder selects the different blocks. The address decoder is
controlled by the control unit board.

3. Regulator

The regulator converts power voltage to 5 VDC.

4. Expansion

Future expansion possibilities. Not used.

5. Board ID

The control unit board reads the IKK-4 ID.

6. Inputs

Reads all external inputs.

7. Outputs

Controls the four transistor outputs.

8. Buzzer

An external buzzer may be connected via a transient protected output. The
buzzer will be parallel connected to the fire alarm and the fault buzzer on the
control unit board.

9. Barrier

The RS 232 communication is protected against transients before entering the
control unit board.

10. System loop barrier

Transient barrier for the system loop.

11. Barrier

The power supply voltage output is protected against external transients.

12. Power supply output

A fused and fault supervised output for power supply to an external device.

13. Opto-isolated inputs

Four opto-isolated transient protected external inputs.

14. Opto-isolated outputs

Four transistor outputs. Deactivated at hang-ups in the programme execution.

Содержание Salwico CS3000




















































































Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды

Consilium Salwico CS3000, Руководство по обслуживанию

Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды