Consilium Salwico CS3000 Скачать руководство пользователя страница 78

Страница: 78 / 83

Document no.:

S-4-007.875/E

Prepared: 2002-10-01

Revision:

R5 2004-04-07 BM

2002, Consilium Marine AB

Service manual

Appendix C: Fault codes C-10

CS3000

142 EARTH

FAULT–

Cause

Remedy

Earth fault between negative terminal and
earth.

See

Earth fault

at the end of this

chapter.

FAULT (142) POWER EARTH FAULT –

Earth fault to minus from the power unit.

145 LOW

VOLTAGE

Cause

Remedy

Too low system voltage from the power
unit.

Test the rectifier and measure the
voltage. If necessary exchange the
rectifier.

146 HIGH VOLTAGE (Abnormal. condition)

Cause

Remedy

Too high system voltage from power unit.

Test the rectifier and measure the
voltage. If necessary exchange the
rectifier.

147 FIRE

PREWARNING

Cause

Remedy

The system has detected a smoke value
approaching the alarm level.

Check the unit.

150 TIMER

STUCK

Cause

Remedy

The timer does not work properly.

Check the unit.

161 DOOR

OPEN

Cause

Remedy

A door is still open one minute after the
instruction to close it was sent.

Check the door.

163 OPEN DOOR SUBLOOP BREAK

Cause

Remedy

Cable break between module and open
door sensor.

Mend the cable.

Содержание Salwico CS3000




















































































Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды

Consilium Salwico CS3000, Руководство по обслуживанию

Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды