manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 51

Service manual CS3000 

Chapter 3: Rack CSR-3200 3-42 

The circuit boards of the central unit 

 

 

Document no.: 

S-4-007.875/E 

Prepared: 

1995-03-17  Fia 

Revision: 

R4  2004-03-15  BM 

 
© 2002, Consilium Marine AB  

 

Rack CSR-3200  

General 

All PCBs in the central unit are mounted in a rack with a back plane. The back 
plane supplies all the PCBs with power and channels for communication 
between them. The rack has room for 14 PCBs. If needed, several racks can be 
inter-connected. The rack fits into a standard 19" cabinet. 

Handling 

Reserved PCB locations 

Certain slots in the rack are reserved for special purposes.  

The relay board ARK-2 must be placed in slot #1 of the first rack and is the 
only board allowed in this slot. If there are more than one rack inter-connected, 
slot #1 in the other racks must be empty.  

The alarm processor board LPK-2 must be placed in slot #2 of the first rack 
and all boards communicating with the LPK-2 via the address and data bus 
must be in the same rack. If there are more than one rack inter-connected, slot 
#2 in the other racks may be used for other purposes. 

If the interface board GSK-2 is used it may be placed in any available slot, 
with the above exceptions. In this case a loop processor board SPK-2 must be 
placed in the last slot (#14) of one of the racks. 

Settings 

The only necessary setting on the rack is made when an interface board GSK-2 
shall be used for the connection of sections with conventional digital detectors. 
In this case a SPK-2 board in slot #14 will be using the internal IDA-loop, and 
therefore the two jumpers S01 and S02 must be set in their upper positions. 
These two jumpers are normally set in their lower positions by the factory. 

Function 

Each board occupies 30 mm of the width of the rack. The slots in each rack are 
numbered #1 - #14. 

If more than one rack shall be inter-connected, this is done with flat cables 
connected to headers on the rear side of the racks. 

In order to prevent noise from loads connected to the relay board ARK-2 from 
interfering with other boards, the power to the rack is divided in two separate 
channels, one supplying the relay board and one for the rest of the rack.  

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды