manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 49

Service manual CS3000 

Chapter 3: Interface board  KPK-2 3-40 

The circuit boards of the central unit 

 

 

Document no.: 

S-4-007.875/E 

Prepared: 

1995-03-17  Fia 

Revision: 

R4  2004-03-15  BM 

 
© 2002, Consilium Marine AB  

 

1. DC/DC converter 

The DC/DC circuit converts the battery voltage of the back plane to 5 VDC, 
which is supplied to all logical circuits on the board. Should the voltage 
disappear, a signal is activated in the back-plane. The DC/DC converter aslso 
supplies the serial port drivers with electric isolated power. 

2. CPU/Memory/Watch-dog 

Contains processor, memory, watch-dog and digital circuitry to provide system 
function. 

3. LED Indications 

The 5 V voltage and proper polling are indicated by green LEDs. Send and 
receive for both the RS485 channels as well as send and receive for the RS232 
channels are also indicated by green LEDs. The serial channels can also be 
enabled/disabled by the CPU. 

4. DUART circuits 

Two of the DUARTs are for the RS232 channels and two is for the RS485 
channels. All parameters, such as baud-rate, parity, etc., are programmable.  
Contains processor two serial ports which is connected to the RS485 
tranceivers. The DUART also control certain I/O  on the board. 

5. Fuse fault 

The battery voltage is fused. If the fuse is blown a signal is activated in the 
back-plane. The fuse is accessible on the front panel of the board, and can be 
used for disconnecting the power. 

6.  &  7. RS232 adaptation 

Adaptations of the signals from 5 V logic to RS232 logic and vice versa. The 
signals from one channel are connected to a D-sub header on the front panel 
and the other are connected to the back plane. 

8.  &  9. RS485 adaptation 

Adaptations of the signals from 5 V logic to RS485 logic and vice versa. The 
signals from both channels are connected to the back plane. 

10.  &  11. Buffers 

The address bus, the data bus and the control signals are buffered before 
entering the board. 

12. Board address 

Selects the board address. 

13. RS232 D-SUB HEADER 

Male 9-pin D-sub header on the front panel with IBM PC/AT pin-standard. 

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды