Consilium Salwico CS3000 Скачать руководство пользователя страница 63

Страница: 63 / 83

Service Manual CS3000

Appendix B: Fault codes

B-6

Fault codes

Document no.:

S-4-007.875/E

Prepared:

1995-03-17 Fia

Revision:

R4 2004-03-15 BM

2002, Consilium Marine AB

84 VOLTAGE

FAULT

Too low voltage in the system.

Cause

Remedy

Internal voltage fault.

Exchange the PCB.

85 I/O-FAULT

An I/O-board is faulty or missing.

Cause

Remedy

Incorrect numbers of I/O-boards.

Correct it.

One of the boards ARK-2, INK-2,
UTK-2, RS232K-2 or KPK-2 is
faulty.

Exchange the board.

POLLUTED DETECTOR (Abnormal condition)

Cause

Remedy

Detector head is polluted.

Optical smoke detector: Clean the
detector head according to the
recommendations.

Ionization smoke detector:
Exchange the detector.

93 FUSE/CABLE

FAULT

A fuse in the central unit is blown or there is a cable break. Different messages

are displayed depending on the location of the fuse.

Cause

Remedy

A fuse is blown in the central
unit.

Exchange the fuse. See

Fuses

the end of this chapter.

Cable break.

Mend the cable. See

Cable break

at the end of this chapter.

FAULT (93) EXT.ALARM 9 FUSE/CABLE FAULT

A fuse blown or a cable break in external alarm device 9.

FAULT (93) BATTERY FUSE/CABLE FAULT

Battery fuse blown, cable break or bad battery in central unit.

101 ALARM FUNCTION FAILURE

Cause

Remedy

The alarm function in the
detector does not work.

Exchange the detector.

Содержание Salwico CS3000




















































































Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды

Consilium Salwico CS3000, Руководство по обслуживанию

Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды