manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 32

Service manual CS3000 

Chapter 3: Output board  UTK-2 3-23 

The circuit boards of the central unit 

 

 

Document no.: 

S-4-007.875/E 

Prepared: 

1995-03-17  Fia 

Revision: 

R4  2004-03-15  BM 

 
© 2002, Consilium Marine AB  

 

Output board UTK-2  

General 

The output board UTK-2 is used for controlling external relays, e.g. for fans 
and fire doors. The UTK-2 board is controlled by the alarm processor board 
LPK-2, via the address and data buses in the back plane.  

The UTK-2 board is equipped with 24 opto-isolated outputs for 24 VDC/50 
mA. The outputs are divided into six groups where each group includes four 
outputs and a common positive conductor.  

Handling 

 

Indications 

In the front panel of the board are two LEDs.  

 

No 1 (green) when lit: 

proper voltage supply. 

No 2 (green) when lit: 

the board is properly polled. 

 

Fuse 

The battery voltage is fused. If the fuse is blown a signal is activated in the 
back-plane. The fuse is accessible on the front panel of the board, and can be 
used for disconnecting the power. 

Fuse rating: 250 mAT  5x20 mm 

 

Setting the address 

The address of the board is set with a DIP-switch (SW1), with 8 switches. The 

address bits #2 - #9 are set. Bit #2 is set with SW1-1, and bit #9 with SW1-8. For more information 
see Appendix A. 

Restarting the board 

Remove the fuse from the board to disconnect the power. When the fuse is put 
back on, the board is restarted. 

Replacing the board 

To replace the UTK-2 follow these steps: 

1.

 

Shut down the central by removing the fuses F3-F6 on the KE-2 rectifier. 

 

WARNING!

  

The power must be disconnected before the board is removed. 

2.

 

Remove the board and replace it with the new board. 

3.

 

Start up the central by inserting F3+F4 and F5+F6 in that order. 

1

2

Salwico UTK-2

 

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды