manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 11

Service manual CS3000 

Chapter 3: Loop processor board SPK-2  3-2 

The circuit boards of the central unit 

 

 

Document no.: 

S-4-007.875/E 

Prepared: 

1995-03-17  Fia 

Revision: 

R4  2004-03-15  BM 

 
© 2002, Consilium Marine AB  

 

Fuse 

The battery voltage is fused. If the fuse is blown a signal is activated in the back 
plane. The fuse is accessible on the front panel of the board, and can be used for 
disconnecting the power.  

Fuse ratings:  

Model 1 & 2: 

1 AT 

  5x20 mm 

Model 3: 

1.6 AT 

  5x20 mm 

Setting the address 

The address of loop #1 of the board is set with a DIP-switch (SW1), with 8 
switches. Bit #1 is set with SW1-1, and bit #8 with SW1-8. The address of loop #2 
is automatically set by the system to the next consecutive value. 

Set the address of each SPK-2 according to the definition in the Definition 
program.  

Restarting the board 

Remove the fuse from the board to disconnect the power. When the fuse is put back 
on, the board is restarted. 

Replacing the board 

To replace the SPK-2 follow these steps: 

1.

 

Disconnect the power by removing the fuse. 

 

WARNING!

  

The power must be disconnected before the board is removed. 

2.

 

Remove the board and replace it with the new board. 

 

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды