manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 41

Service manual CS3000 

Chapter 3: Interface board  RS232K-2 3-32 

The circuit boards of the central unit 

 

 

Document no.: 

S-4-007.875/E 

Prepared: 

1995-03-17  Fia 

Revision: 

R4  2004-03-15  BM 

 
© 2002, Consilium Marine AB  

 

Interface board RS232K-2  

General 

The RS232K-2 is an addressable interface board used for connecting the 
CS3000 system to external computers, modems, terminals, mimics, serial 
printers, etc.  

The board is equipped with two RS232 channels and two RS485 channels. 
One of the RS232 channels is accessible through a D-sub header on the front 
panel and the other channels are connected via the back-plane. 

The RS232K-2 is controlled by LPK-2 via the address and data buffers in the 
back plane. All channels are programmable for baud-rate and other 
communication parameters. The functions of the board are set by the definition 
programme. 

Handling 

 

Indications 

There are ten green LEDs on the front panel of the board.  
No 1  when lit: proper voltage supply. 
No 2  when lit: the board is properly polled. 
No 3  when lit: RS232 channel #2 sending. 
No 4  when lit: RS232 channel #2 receiving. 
No 5  when lit: RS232 channel #2, RTS active. 
No 6  when lit: RS232 channel #2, CTS active. 
No 7  when lit: RS485 channel #1 sending. 
No 8  when lit: RS485 channel #1 receiving. 
No 9  when lit: RS485 channel #2 sending. 
No 10 when lit: RS485 channel #2 receiving. 

Fuse 

The battery voltage is fused. If the fuse is blown a signal is activated in the 
back plane. The fuse is accessible on the front panel of the board, and can be 
used for disconnecting the power. 

Fuse rating: 250 mAT  5x20 mm 

 

Setting the address 

The address of the board is set with a DIP-switch (SW1). The address bits #5 - 
#9 are set. Bit #5 is set with SW1-4.  The address of each RS232K-2 board is 
set according to the definition in the Definition program. For more information 
see Appendix A. 

 

1

2

3

4

5

6

7

8

9

10

Salwico RS232K-2

 

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды