manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 35

Service manual CS3000 

Chapter 3: Output board  UTK-2 3-26 

The circuit boards of the central unit 

 

 

Document no.: 

S-4-007.875/E 

Prepared: 

1995-03-17  Fia 

Revision: 

R4  2004-03-15  BM 

 
© 2002, Consilium Marine AB  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Choice of source/sink outputs  

Each of the 24 outputs can be individually chosen for source or sink outputs by 
means of the jumpers on the PCB (see picture above). The outputs on the PCB 
are grouped, with four outputs in each group. Each output has two jumpers (i e 
eight jumpers per group).   

 

The jumpers are factory set (as in the picture) for source output on all lines. 

 

 

 

 

 

 

 

 

Jumpers

              SOURCE                                       SINK 

Output group configuration.  4 outputs per group 

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды