manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 24

Service manual CS3000 

Chapter 3: Relay board  ARK-2 3-15 

The circuit boards of the central unit 

 

 

Document no.: 

S-4-007.875/E 

Prepared: 

1995-03-17  Fia 

Revision: 

R4  2004-03-15  BM 

 
© 2002, Consilium Marine AB  

 

 

Jumper "PLUS" 

With this jumper the pulse type can be altered. In the left position the pulse is 
internally generated, in the right position the pulse comes from an external 
source. 

Switch S9 

This switch is found on the front panel and is used for resetting the basic-
alarm. 

Switch SW1 

SW1-1, SW1-2, SW1-3  (B1, B2, B3)  

"ON" : Steady signal to corresponding alarm bell output. 

"OFF": Pulsed signal to corresponding alarm bell output. 

 

SW1-4, SW1-5, SW1-6  (R1, R2, R3) 

"ON" : Steady signal to the outputs of relays RL1-RL3. 

"OFF": Pulsed signal to the outputs of relays RL1-RL3. 

 

SW1-7  (GA) 

"ON" : Signal in step with the signal on the GA-input. 

"OFF": Pulsing signal 

Replacing the board 

To replace the ARK-2 follow these steps: 

1.

 

Shut down the central by removing the fuses F3-F6 on the KE-2 rectifier. 

 

WARNING!

  

The power must be disconnected before the board is removed. 

2.

 

Remove the board and replace it with the new board. 

3.

 

Start up the central by inserting F3+F4 and F5+F6 in that order. 

 

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды