Consilium Salwico CS3000 Скачать руководство пользователя страница 60

Страница: 60 / 83

Service Manual CS3000

Appendix B: Fault codes

B-3

Fault codes

Document no.:

S-4-007.875/E

Prepared:

1995-03-17 Fia

Revision:

R4 2004-03-15 BM

2002, Consilium Marine AB

BAD ANSWER (Abnormal condition)

Bad communication with one section unit or several section units, could be

temporary. This fault code is sent when an interference in the communication is

detected.

Cause

Remedy

Bad communication with one or
several section units.

Exchange the section unit if the
condition remains or returns.

22 NO

ANSWER

No polling answer from a section unit.

Cause

Remedy

Wrong type of section unit.

Exchange to the correct section
unit.

Two section units have the same
address.

Check the units.

Hardware fault

Exchange the unit.

A fuse is blown. A secondary
fault appears, code (83).

Exchange the fuse.

Cable break in a loop or system
loop. A secondary fault
APPEARS, code (121).

Mend the cable. See

Cable break

at the end of this chapter.

24 WRONG

STATUS

Incorrect answer from the section unit.

Cause

Remedy

Section unit faulty

Exchange the section unit.

25 WRONG

The software does not recognise the ID of a section unit.

Cause

Remedy

Section unit faulty.

Exchange the section unit.

Wrong software in CS3000.

Exchange the software.

Wrong type of detector has been
installed.

Install the correct type of detector.
Restart the system.

Содержание Salwico CS3000




















































































Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды

Consilium Salwico CS3000, Руководство по обслуживанию

Результаты поиска

Содержание Salwico CS3000

Отзывы:

Бренды по названию

Популярные бренды