manualshive.com logo in svg

Consilium Salwico CS3000, Руководство по обслуживанию

Поделиться
Скачать
Consilium Salwico CS3000 Скачать руководство пользователя страница 71

Document no.: 

S-4-007.875/E 

Prepared: 2002-10-01 

BM 

Revision: 

R5  2004-04-07 BM 

 

©

 2002, Consilium Marine AB  

 

Service manual 

Appendix C: Fault codes  C-3 

CS3000 
 
 

 

12 

SUBCENTRAL MISSING DEF. DATA 

 

 

Cause

 

Remedy

 

The sub-central has not been defined 
properly at the installation. 

Define the sub-central. 

 

13 

WRONG TYPE OF CONTROL UNIT 

 

 

Cause

 

Remedy

 

Wrong definition at the installation of the 
control unit. 

Redefine the sub-central. 

 

21 

BAD ANSWER (Abnormal condition) 

 

Bad communication with one loop unit or several loop units, this could be 
temporary. This fault code is sent when interference in the communication is 
detected. 

 

Cause Remedy

 

Bad communication with one or several 
loop units. 

Exchange the loop unit if the 
condition remains or returns. 

 

22 NO 

ANSWER 

 

The loop unit doesn't answer. 

 

Cause

 

Remedy

 

Wrong type of section unit. 

Exchange to the correct section 
unit. 

Two loop units have the same address. 

Check the units. 

Hardware fault 

Exchange the unit. 

A fuse is blown. A secondary fault 
appears, code (83). 

Exchange the fuse. 

Cable break in a loop or system loop. A 
secondary fault APPEARS, code (121). 

Mend the cable. See 

Cable break  

at the end of this chapter. 

 
24 

WRONG IDA STATUS 

 

Incorrect answer from the loop unit. 

 

Cause

 

Remedy

 

Loop unit faulty 

Exchange the loop unit. 

 

Содержание Salwico CS3000




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды