ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 25 / 632

InteliLite Global Guide

IMPORTANT: When the controller is power up only by USB and the USB is disconnected then the

actual statistics is lost.

Note:

Suitable conductor protection shall be provided in accordance with NFPA 70, Article 240.

Note:

Low voltage circuits (35 volts or less) shall be supplied from the engine starting battery or an isolated

secondary circuit.

Power supply fusing

A two-amp fuse should be connected in-line with the battery positive terminal to the controller and modules.

These items should never be connected directly to the starting battery. Fuse value and type depends on number

of connected devices and wire length. Recommended fuse (not fast) type - T2A. Not fast due to internal

capacitors charging during power up.

IMPORTANT: 2 A fuse is calculated without BOUT consumption nor extension modules. Real value

of fuse depends on consumption of binary outputs and modules.

Example:

Maximal consumption of binary outputs can be 22 A

2 x 10 A on high current outputs (for 10 seconds)

2 A on all others binary outputs

4.4.4 Measurement wiring

Use 1.5 mm

cables for voltage connection and 2.5 mm

for current transformers connection. Adjust

Connection

type (page 157)

Nominal Voltage Ph-N (page 158)

Nominal Voltage Ph-Ph (page 159)

Nominal Current (page

156)

PT Ratio (page 159)

and

CT Ratio (page 157)

by appropriate setpoints in the Basic Settings group.

IMPORTANT: Risk of personal injury due to electric shock when manipulating voltage terminals

under voltage. Be sure the terminals are not under voltage before touching them.

Do not open the secondary circuit of current transformers when the primary circuit is closed. Open

the primary circuit first.

Current measurement wiring

The number of CT’s is automatically selected based on selected value of setpoint

Connection type (page 157)

[3Ph4Wire / High Leg D / 3Ph3Wire / Split Ph / Mono Ph].

Generator currents and power measurement is suppressed if current level is bellow <1% of CT range.

To ensure proper function:

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды