ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 332 / 632

InteliLite Global Guide

332

Setpoint group

CM-Ethernet

Related FW

1.2.1

Range [units]

FIXED / AUTOMATIC [-]

Default value

AUTOMATIC

Alternative config

Step

[-]

Comm object

24259

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Only if relevant module is installed

Description

The setpoint is used to select the method how the ethernet connection is adjusted.

FIXED:

The ethernet connection is adjusted fixedly according to the setpoints

IP Address (page

332)

Subnet Mask (page 333)

Gateway IP (page 333)

and

DNS IP Address 1 (page 334)

This option is reccomended for Direct IP connection as the IP address of the device

should be static for this connection type.

AUTOMATIC:

The Ethernet connection setting is obtained automatically from the DHCP server. The

obtained settings are visible in the values and the setpoints do not take place. Use this

option if you connect to the device only via AirGate or if you assure obtaining a static IP

address at the DHCP side.

IP Address Mode

back to List of setpoints

Setpoint group

CM-Ethernet

Related FW

1.2.1

Range [units]

Valid IP address [-]

Default value

192.168.1.254

Alternative config

Step

[-]

Comm object

24376

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Only if relevant module is ins conditioned by the setpoint

IP Address Mode (page

332)

Description

The setpoint is used to select the method how the IP Address is adjusted.

IP Address Mode (page 332)

is FIXED this setpoint is used to adjust the IP address of the ethernet interface

of the controller. Ask your IT specialist for help with this setting.

IP Address Mode (page 332)

is AUTOMATIC this setpoint is inactive. The IP address is assigned by the

DHCP server.

IP Address

back to List of setpoints

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды