ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 95 / 632

InteliLite Global Guide

Image 5.24 Daily mode - LiteEdit2015

In timer mode select Repeat. In repetition type select Daily. In timer settings adjust date and time of first

occurrence of timer. Also adjust the duration of each occurrence of timer. Than select the x-th day of repetition

(

Timer 1 Refresh Period (page 268)

) and behavior of timer on weekends (

Timer 1 Weekends (page 269)

Example:

On image example first start of timer will be 1/1/2016 at 12:00. Duration will be 1 hour. Timer will

be again activated every 3rd day at 12:00 for 1 hour including weekends.

Set-up via controller interface

In controller go to the Scheduler setpoint group. Select the function of timer via

Timer 1 Function (page 264)

setpoint. Than go to

Timer 1 Setup

and press enter button. In

Timer 1 Repetition (page 265)

setpoint select

Repeated mode. Than adjust

Timer 1 First Occur. Date (page 266)

Timer 1 First Occur. Time (page 266)

and

Timer 1 Duration (page 266)

. In setpoint

Timer 1 Repeated (page 267)

select Daily and adjust

Timer 1 Refresh

Period (page 268)

(x-th day of repetition) and

Timer 1 Weekends (page 269)

(behavior of timer on weekends).

Note:

Use left and right buttons to move between timer setpoints.

Weekly mode

Set-up via LiteEdit2015

To set-up timer via LiteEdit2015 go to the setpoint ribbon, setpoint group scheduler and setpoint

Timer 1 Setup

Note:

First of all function of timer has to be adjusted via setpoint

Timer 1 Function (page 264)

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды