ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 36 / 632

InteliLite Global Guide

Image 4.13 Wiring of analog input with current sensor

0 - 22 mA

100

133

167

202

241

283

328

375

431

489

553

625

707

793

894

1007

1136

1287

1460

1666

1914

2222

2596

Note:

This is a conversion of current from current sensor to appropriate resistance value. Use resistance

values in LiteEdit2015 to create your specific curve. These values should be used in "Ohm" column.

4.4.10 CAN bus and RS485 wiring

CAN bus wiring

The wiring of the CAN bus communication should be provided in such a way that the following rules are

observed:

The maximum length of the CAN bus depends on the communication speed. For a speed of 250 kbps, which

is used on the CAN1 bus (extension modules, ECU), the maximum length is 200 m.

The bus must be wired in linear form with termination resistors at both ends. No nodes are allowed except on

the controller terminals.

Shielded cable

has to be used, shielding has to be connected to the terminal T01 (BATT -).

External units can be connected on the CAN bus line in any order, but keeping line arrangement (no tails, no

star) is necessary.

Recommended data cables: BELDEN (

http://www.belden.com

) - for shorter distances: 3105A Paired - EIA

Industrial RS-485 PLTC/CM (1x2 conductors); for longer distances: 3106A Paired - EIA Industrial RS-485

PLTC/CM (1x2+1 conductors)

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды