ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 278 / 632

InteliLite Global Guide

278

Setpoint group

Scheduler

Related FW

1.2.1

Range [units]

1 .. 5 [week]

Default value

1 week

Alternative config

Step

1 week

Comm object

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Conditioned by the setpoint

Timer 2 Function (page 271)

Description

This setpoint adjust the week of month in which the

Timer 2 Function (page 271)

will be activated.

Timer 2 Repeat Week In Month

back to List of setpoints

Subgroup: Rental Timers

Setpoint group

Scheduler

Related FW

1.2.1

Range [units]

Disabled / 1 .. 8 760 [h]

Default value

Disabled

Alternative config

Step

1 h

Comm object

14326

Related applications

AMF, MRS

Config level

Advanced

Setpoint visibility

Always

Description

Another engine start is not allowed when this timer elapsed. This timer is based on engine running hours. The

alarm

Rental Timer 1 Elapsed (page 566)

will be recorded in alarm list and the binary output

will close.

IMPORTANT: To reset

Rental Timer 1 (page 278)

we have to set up

Rental Timer 1 (page 278)

again. It means go to setpoint group Scheduler and to the setpoint

Rental Timer 1 (page 278)

Then press enter button

, change the value if it is necessary and press enter button

again.

When the

Rental Timer 1 (page 278)

elapsed during engine run the gen-set will not stop immediately. The

adjustable

Rental Timer BOC (page 282)

timer will start in this moment. The engine will be cooled and stopped

when the

Rental Timer BOC (page 282)

time elapsed.

Rental Timer 1

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды