ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 628 / 632

InteliLite Global Guide

628

Binary outputs

8 channels

can be configured as:

High side switch

Low side switch

Always all 8 inputs are configured to one type (HSS/LSS) together. All 8 outputs can be modified to inputs by

switch on the PCB ( Inteli IO8/8 to Inteli IO 16/0).

Analog outputs

2 channels

can be configured as:

voltage 0-10V

current 0-20mA

PWM (level 5V, with adjustable frequency from 200Hz to 2400Hz, with step 1Hz)

All inputs/outputs can be configured to any logical function or protection.

Output state check

Output state check function evaluates in real time the state of binary outputs and adjusted (required) state. In

case of failure (different state of required state and real state) history record and alarm are issued (type of the

alarm is set by “Protection upon module failure” - (No protection / Warning / Shutdown)).

This function is designed for short-circuit or other failure, which causes change of set state of binary output.

CAN address

In Inteli IO8/8 mode CAN address for binary inputs is determined by DIP switch A, CAN address for binary

output and analog outputs is determined by DIP switch B.

In Inteli IO 16/0 mode CAN address for binary inputs is determined by DIP switch A, first group of 8 input has

address A, second group of 8 inputs has address A+1. CAN address of analog outputs is set by DIP switch B.

Note:

In case of setting the CAN address to zero, the appropriate group of signals is deactivated.

Programming firmware

Firmware upgrade process:

1. Disconnect all terminals from the unit.

2. Separate the top cover of module

3. Put the TEST jumper on a pins

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды