ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 99 / 632

InteliLite Global Guide

Short period mode

Set-up via LiteEdit2015

To set-up timer via LiteEdit2015 go to the setpoint ribbon, setpoint group scheduler and setpoint

Timer 1 Setup

Note:

First of all function of timer has to be adjusted via setpoint

Timer 1 Function (page 264)

Image 5.28 Short period mode - LiteEdit2015

In timer mode select Repeat. In repetition type select Short period. In timer settings adjust date and time of first

occurrence of timer. Also adjust the duration of each occurrence of timer. Than select the interval of repetition

(shorter than 1 day).

Example:

On image example first start of timer will be 1/1/2016 at 12:00. Duration will be 1 hour. Timer will

be again activated every 4th hour for 1 hour.

Set-up via controller interface

In controller go to the Scheduler setpoint group. Select the function of timer via

Timer 1 Function (page 264)

setpoint. Than go to

Timer 1 Setup

and press enter button. In

Timer 1 Repetition (page 265)

setpoint select

Repeated mode. Than adjust

Timer 1 First Occur. Date (page 266)

Timer 1 First Occur. Time (page 266)

and

Timer 1 Duration (page 266)

. In setpoint

Timer 1 Repeated (page 267)

select Short Period and adjust

Timer 1

Refresh Period (page 268)

(interval of repetition).

Note:

Use left and right buttons to move between timer setpoints.

5.4.12 Rental Timers

In controller are two timers which are designed like rental timer. Rental timers will stop gen-set after their

elapse.

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды