ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 605 / 632

InteliLite Global Guide

605

operating mode with communication with controller - green LED is blinking in period 500ms/500ms

operating mode without communication with controller - red LED is blinking in period 500ms/500ms

test mode - green LED is blinking in period 250ms/250ms

Firmware upgrade

Download the newest FW of module from ComAp website (in form of PSI file or installation package)

Instal package to computer or open PSI to instal it into LiteEdit2015

Plug the module into the controller and power the controller on.

Open a connection with controller via LiteEdit2015

Go the menu Tools -> Firmware upgrade, select the Plug-in modules tab and select the appropriate firmware

you want to program into the module (in LiteEdit2015).

Press the OK button to start upgrade of firmware.

The firmware update process may be performed via any kind of connection including connection via the same

module in which the firmware is to be updated. The connection is reestablished again automatically when the

update process is finished.

CM-GPRS

CM-GPRS plug-in module is a GSM/GPRS modem which can works in two modes of operation based on the

settings in the setpoint

Mode (page 314)

Image 9.19 CM-GPRS module

IMPORTANT: Any manipulation with plug-in module shall be done with disconnected power

supply to controller.

IMPORTANT: CM-4G-GPS and CM-GPRS modules cant be used in one controller in the same time.

Note:

GPRS and CSD services must be provided by your GSM/GPRS operator for successful operation.

Note:

The GPRS and CSD connection should not be used for the firmware update process.

CM-GPRS module works with:

WebSupervisor – internet-based remote monitoring solution

AirGate – powerful connection technology to make internet access as simple as possible

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды