ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 87 / 632

InteliLite Global Guide

Events

specification

Protection

type

Description

Analog Input 2 Sd

Value measured on analog input 2 is </> than

Analog Protection 2 Sd

(page 206)

setpoint.

Analog Input 3 Wrn

WRN

Value measured on analog input 3 is </> than

Analog Protection 3

Wrn (page 208)

setpoint.

Analog Input 3 Sd

Value measured on analog input 3 is </> than

Analog Protection 3 Sd

(page 209)

setpoint.

Analog Input 4 Wrn

WRN

Value measured on analog input 4 is </> than

Analog Protection 4

Wrn (page 211)

setpoint.

Analog Input 4 Sd

Value measured on analog input 4 is </> than

Analog Protection 4 Sd

(page 212)

setpoint.

Wrn Battery Voltage

WRN

Battery voltage is out of limits given by

Battery < Voltage (page 190)

and

Battery > Voltage (page 190)

setpoints.

Binary input

Configurable Warning/BOC/Shutdown alarms on the binary inputs.

Sd Battery Flat

If the controller switches off during starting sequence (

output is active) it doesn’t try to start again and activates

this protection (controller assumes bad battery condition).

Sd Start Fail

Gen-set start failed. All crank attempts were tried without success.

Parameters Fail

NONE

Wrong check-sum of parameters. Happens typically after

downloading new firmware or changing of the parameter. The

controller stays in INIT mode. Check all parameters, change value of

at least one parameter.

Sd Gen Lx >V

BOC Gen Lx <V

(where x=1,2,3)

BOC

The generator voltage is out of limits given by Gen <V BOC and Gen

>V Sd setpoints.

BOC Gen V

Unbalance

BOC

The generator voltage is unbalanced more than the value of

Voltage

Unbalance BOC (page 200)

setpoint.

BOC Gen >,

<Frequency

BOC

The generator frequency is out of limits given by

Generator >

Frequency BOC (page 201)

and

Generator < Frequency BOC (page 201)

setpoints.

BOC Current

Unbalance

BOC

The generator current is unbalanced more than the value of

Current

Unbalance BOC (page 197)

setpoint.

BOC Current IDMT

BOC

Generator current exceeds the limit for IDMT protection given by

Nominal Current (page 156)

and

IDMT Overcurrent Delay (page 196)

setpoints.

BOC Overload

BOC

The load is greater than the value given by

Overload BOC (page 194)

setpoint.

Sd Earth Fault

This alarm is activated when Earth Fault value exceeds

Earth Fault

Sd (page 340)

limit for at least

Earth Fault Delay (page 339)

period.

Sd Overspeed

The protection comes active if the speed is greater than

Overspeed Sd

(page 175)

setpoint.

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды