ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 82 / 632

InteliLite Global Guide

Duration of the cool down phase is determined by the setpoint

Cooling Time (page 174)

Cooling is performed either at nominal speed (generator voltage and frequency protections are evaluated) or

at idle speed (generator voltage and frequency protections are not evaluated). Selection of the speed is done

by the setpoint

Cooling Speed (page 173)

The cool down can be finished manually in MAN mode by pressing the STOP button.

If a new start request comes, the cool down will be interrupted and the gen-set will go back to the

stabilization phase. If the cooling was at nominal speed, the stabilization timers will not count down again so

the GCB is ready to be closed (after 2 seconds delay).

When the cool down is finished, the output

is de-energized and

is energized. The engine will stop within the time period determined by the setpoint

Stop Time (page

174)

. If the engine does not stop within this time, the alarm

Wrn Stop Fail (page 576)

will be issued.

The output

is energized until the engine is stopped, but at least for the duration of

Stop Time (page 174)

. If the

Stop Time (page 174)

has elapsed and the engine has still not stopped, the

is de-energized for 5 s and then energized again for

Stop Time (page 174)

and this repeats

until the engine is stopped.

The output

Ignition (page 503)

is continuously energized until the engine is stopped.

Stopped gen-set evaluation

The gen-set is considered as stopped when all of following conditions are valid:

The engine speed is lower than 2 RPM.

The generator voltage in all phases is lower than 10 V.

None of

Additional running engine indications (page 103)

signals is active.

5.4.8 Alarm management

The controller evaluates two levels of alarms. Level 1 – yellow alarm – is a pre-critical alarm that is only

informative and does not take any action regarding gen-set control. Level 2 – red alarm – represents a critical

situation, where an action must be taken to prevent damage of the gen-set or technology.

One alarm of any type can be assigned to each binary input

Two alarms (one yellow and one red type) can be assigned to each analog input

There are also

Built-in alarms (page 86)

with fixed alarm types.

Each alarm is written to the

Alarmlist (page 86)

Each alarm causes a record to be written into the history log.

Each alarm activates the Alarm and Horn output.

Each alarm can cause sending of a SMS message or an email.

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды