ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 103 / 632

InteliLite Global Guide

103

5.4.16 Additional running engine indications

It is helpful to have information other than speed (RPM), whether the engine is rotating or not, especially if RPM

is measured from the generator frequency instead of magnetic pickup. The generator frequency measurement

can be unreliable at very low speeds and/or may have a delayed reaction to sudden and big changes (i.e. in the

moment that the engine has just started…).

The following conditions are evaluated as additional running engine indication:

Voltage on the D+ input is higher than 80% of battery voltage. Connect this input to the D+ (L) terminal of the

charging alternator and enable the D+ function by the setpoint D+ Function. If D+ terminal is not available,

leave the input unconnected and disable the function.

The pickup is not used and frequency is not detected on the pickup input. Connect the pickup input to the W

terminal of the charging alternator if you do not use pickup and the W terminal is available. If not, leave the

input unconnected.

Oil pressure >

Starting Oil Pressure (page 167)

setpoint. The oil pressure is evaluated from the analog input or

from the ECU if an ECU is configured.

At least one phase of generator voltage is >25% of nominal voltage.

These signals are used during start for powering down the starter motor even if still no RPM is measured and

also during stop in order to evaluate if the engine is really stopped.

5.4.17 Voltage phase sequence detection

Controller detects phase sequence voltage terminals. This protection is important after controller installation to

avoid wrong voltage phase connection. There is fix defined phase sequence in controller L1, L2, L3. When the

phases are connected in different order (e.g. L1,L3,L2 or L2,L1,L3) following alarms are detected:

Generator CCW Rotation (page 578)

5.4.18 Gen-set operation states

Engine state machine

Init

Autotest during controller power on.

Not ready

Gen-set is not ready to start.

Example:

When shutdown alarm is active or unit is in OFF mode.

Prestart

Prestart sequence in process,

output is closed.

Example:

Usually used for preheating or processes executed prior gen-set start.

Cranking

Engine is cranking,

output is closed

Pause

Pause between start attempts.

Starting

Starting speed is reached and the Idle timer is running.

Running

Gen-set is running at nominal speed.

Loaded

Gen-set is running at nominal speed and

is closed.

Stop

Stop.

Example:

Automatic or manual stop command was issued, engine is stopping.

Shutdown

Shut-down alarm activated.

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды