ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 338 / 632

InteliLite Global Guide

338

Setpoint group

CM-GPRS; CM-4G-

GPS; CM-Ethernet

Related FW

1.2.1

Range [units]

0 .. 65 535[-]

Default value

Alternative config

Step

[-]

Comm object

24374

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Only if relevant module is ins conditioned by the setpoint

Mode (page 314)

(CM-

GPRS module)

Description

This setpoint is used to adjust the port number, which is used for Ethernet connection to a PC with any of

ComAp PC program (i.e. LiteEdit2015). This setpoint should be adjusted to 23, which is the default port used

by all ComAp PC programs. A different value should be used only in special situations as e.g. sharing one

public IP address among many controllers or to overcome a firewall restrictions.

IMPORTANT: If AirGate is used, this setpoint has to be adjusted to 23.

Note:

This setpoint is common for CM-Ethernet, CM-GPRS and CM-4G-GPS modules.

ComAp TCP Port

back to List of setpoints

Group: EM-BIO8-EFCP

Setpoint group

EM-BIO8-EFCP

Related FW

1.2.1

Range [units]

DISABLED / ENABLED [-]

Default value

ENABLED

Alternative config

Step

[-]

Comm object

11631

Related applications

AMF, MRS

Config level

Standard

Setpoint visibility

Only if relevant module is installed

Description

This setpoint can block or allow Earth fault Current protection.

DISABLED

Earth fault current protection is blocked.

ENABLED

Earth fault current protection is allowed. Behavior of Earth fault current protection is set

by these setpoints:

Earth Fault CT Input Range (page 339)

Earth Fault CT Ratio (page

339)

Earth Fault Delay (page 339)

and

Earth Fault Sd (page 340)

Earth Fault Current Protection

back to List of setpoints

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды