ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 619 / 632

InteliLite Global Guide

619

Modbus rate (P13 and P14)

Modbus rate is set by jumpers P13 and P14; description is in the table bellow.

Modbus rate

P13

P14

9600 bps

Open

19200 bps

Open

38400 bps

Open

57600 bps

Direct / Modem (P18)

Select between direct connection via RS232 or RS485 and modem connection type. For modem connection is

jumper P18 closed, for direct connection is jumper P18 opened.

ADR1 / ADR2 (P17)

Select device address. ADR1 is selected if P17 is opened and ADR2 is selected if P17 is closed.

SW / HW control (P15)

Select SW or HW modem control. Jumper P15 is opened for HW modem control and closed for SW modem

control.

RS485 bias resistor (P20 and P21)

Jumpers P20 and P21 are opened if the bias resistors (560R) are not requested. Closed jumper connects bias

resistor to the line A (P20) or B (P21).

USB interface enable/disable (P8)

Jumper P8 has to be set to enable USB interface. Opened jumper disables USB interface (disabled USB

doesn’t occupies a communication channel on the CAN bus i.e. there are still 3 free communications channels

on the CAN bus). USB interface allows only local communication (modbus is not implemented in this interface).

Jumper

Description

State

CAN terminating resistor

Opened - not connect

RS485 terminating resistor

Opened - not connect

RS232 or RS485

1 - 2 RS485 activated, 2 - 3 RS232 activated

USB enable/disable

Opened - disabled

P13

Modbus rate

Opened

P14

Modbus rate

Opened - 9600 bps

P15

HW or SW modem control

Opened - HW control

P16

ComAp or Modbus

Opened - ComAp protocol

P17

ADR1 or ADR2

Opened - ADR1

P18

Direct or Modem

Opened - Direct

Default jumpers settings

Programming firmware

1. Disconnect all terminals from the unit.

2. Disassemble the unit.

3. Put the BOOT jumper on a pin.

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды