ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 591 / 632

InteliLite Global Guide

591

Related applications

AMF, MRS

Description

This alarm evaluates the generator frequency in the phase L1. The following

setpoints are related to it:

Generator < Frequency BOC (page 201)

Generator <> Frequency BOC Delay (page 202)

back to List of alarms level 2

Alarm Type

Shutdown

Alarmlist message

Sd Generator Voltage Unbalance Ph-Ph

Alarm evaluated

Generator excited only

Related applications

AMF, MRS

Description

This alarm evaluates the unbalance of the phase to phase voltage, i.e. the

difference between highest and lowest phase to phase voltage at any given time.

The following setpoints are related to it:

Voltage Unbalance BOC (page 200)

adjusts the maximum allowed difference

between the highest and lowest phase voltage at any given time.

Voltage Unbalance BOC Delay (page 200)

adjusts the alarm delay.

Sd Generator Voltage Unbalance Ph-Ph

back to List of alarms level 2

Alarm Type

Shutdown

Alarmlist message

Sd Generator Voltage Unbalance Ph-N

Alarm evaluated

Generator excited only

Related applications

AMF, MRS

Description

This alarm evaluates the unbalance of the phase voltage, i.e. the difference

between highest and lowest phase voltage at any given time. The following

setpoints are related to it:

Voltage Unbalance BOC (page 200)

adjusts the maximum allowed difference

between the highest and lowest phase voltage at any given time.

Voltage Unbalance BOC Delay (page 200)

adjusts the alarm delay.

Sd Generator Voltage Unbalance Ph-N

back to List of alarms level 2

Alarm Type

Shutdown

Alarmlist message

Sd Oil Pressure

Alarm evaluated

All the time

Related applications

AMF, MRS

Description

This alarm indicates that the oil pressure is lover than the pressure set in

Oil

Pressure Sd (page 177)

setpoint.

Sd Oil Pressure

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды