ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 603 / 632

InteliLite Global Guide

603

Image 9.15 Pinout of RS-232 line

Image 9.16 Pinout of RS-485 line

Note:

Balancing resistors shall be both closed at only one device in whole RS485 network.

Maximal distance of line is 10m for RS232 line and 1200m for RS485 line.

Firmware upgrade

Download the newest FW of module from ComAp website (in form of PSI file or installation package)

Instal package to computer or open PSI to instal it into LiteEdit2015

Plug the module into the controller and power the controller on.

Open a connection with controller via LiteEdit2015

Go the menu Tools -> Firmware upgrade, select the Plug-in modules tab and select the appropriate firmware

you want to program into the module (in LiteEdit2015).

Press the OK button to start upgrade of firmware.

The firmware update process may be performed via any kind of connection including connection via the same

module in which the firmware is to be updated. The connection is reestablished again automatically when the

update process is finished.

CM-Ethernet

CM-Ethernet is a plug-in card with Ethernet 10/100 Mbit interface in RJ45 connector. It provides an interface for

connecting a PC with through ethernet/internet network, for sending active e-mails and for integration of the

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды