ComAp InteliLite MRS16 Скачать руководство пользователя

Страница: 608 / 632

InteliLite Global Guide

608

SIMCom: HW reset issued

PUK is required

Error of SIM card detected

ME909s: can't set module bps

ME909s: can't set link configuration

ME909s: can't do power-off

ME909s: can't do power-on

ME909s: can't do hardware reset

ME909s: ME909s not started

ME909s: switch off issued

ME909s: switch on issued

ME909s: HW reset issued

ME909s: can't switch echo off

ME909s: can't find out state of registration

ME909s: GSM signal not found

ME909s: no SIM memory for SMS

ME909s: waiting for registration

Can't read operator name

ME909s: can't set flow control

APN not typed

255

Only running communication is needed to indicate

AirGate Diag – Diagnostic Code for AirGate connection

Code

Description

Waiting for connection to AirGate Server

Controller registered, waiting for authorization

Not possible to register, controller blacklisted

Not possible to register, server has no more capacity

Not possible to register, other reason

Controller registered and authorized

Firmware upgrade

Download the newest FW of module from ComAp website (in form of PSI file or installation package)

Instal package to computer or open PSI to instal it into LiteEdit2015

Plug the module into the controller and power the controller on.

Open a connection with controller via LiteEdit2015

Go the menu Tools -> Firmware upgrade, select the Plug-in modules tab and select the appropriate firmware

you want to program into the module (in LiteEdit2015).

Press the OK button to start upgrade of firmware.

Содержание InteliLite MRS16

























































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды

ComAp InteliLite MRS16, Руководство пользователя

Результаты поиска

Содержание InteliLite MRS16

Отзывы:

Похожие инструкции для InteliLite MRS16

Бренды по названию

Популярные бренды