20-71
Cisco ONS 15454 SDH Procedure Guide, R7.0
78-17194-01
Chapter 20 DLPs D300 to D399
DLP- D364 Provision Multiplex-Section DCC Terminations
DLP-D364 Provision Multiplex-Section DCC Terminations
Note
When MS-DCC is provisioned, an RS-DCC termination is allowed on the same port, but is not
recommended. Use RS-DCC and MS-DCC on the same port only during a software upgrade if the
software version does not support MS-DCC. You can provision RS-DCCs and MS-DCCs on different
ports in the same node.
Step 1
In node view, click the
Provisioning > Comm Channels
> MS-DCC
tabs.
Step 2
Click
Create.
Step 3
In the Create MS-DCC Terminations dialog box, click the ports where you want to create the MS-DCC
termination. To select more than one port, press the Shift key or the Ctrl key.
Note
MS-DCC refers to the multiplex-section DCC, which is used for ONS 15454 SDH DCC
terminations. The SDH multiplex-section DCCs and the regenerator-section DCC (when not
used as a DCC termination by the ONS 15454 SDH) can be provisioned as DCC tunnels. See the
“DLP-D361 Create a DCC Tunnel” task on page 20-66
Step 4
In the Port Admin State area, click the
Set to IS
radio button.
Step 5
Verify that the Disable OSPF on DCC Link check box is unchecked.
Step 6
If the RS-DCC termination is to include a non-ONS node, check the
Far End is Foreign
check box. This
automatically sets the far-end node IP address to 0.0.0.0, which means that any address can be specified
by the far end. To change the default to a specific the IP address, see the
Regenerator-Section DCC Termination” task on page 20-65
Step 7
In the Layer 3 box, perform one of the following:
•
Check the IP box only—if the MS-DCC is between the ONS 15454 SDH and another ONS node and
only ONS nodes reside on the network. The MS-DCC will use PPP.
•
Check the IP and OSI boxes—if the MS-DCC is between the ONS 15454 SDH and another ONS
node and third party NEs that use the OSI protocol stack are on the same network. The MS-DCC
will use PPP.
Purpose
This task creates the SDH MS-DCC terminations required for alarms,
administration data, signal control information, and messages. MS-DCCs
are three times larger than RS-DCCs. In this task, you can also set up the
node so that it has direct IP access to a far-end non-ONS node over the
DCC network. In addition, you can set up the node so that it has direct IP
access to a far-end non-ONS node over the DCC network. In addition, this
task can create an OSI subnetwork point of attachment on the DCC to allow
the node to be networked with third party NEs that are based on the OSI
protocol stack.
Tools/Equipment
None
Prerequisite Procedures
DLP-D60 Log into CTC, page 17-49
Required/As Needed
As needed
Onsite/Remote
Onsite or remote
Security Level
Provisioning or higher
Содержание ONS 15454 SDH
