Canon MultiPASS L60 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 341

Canon MultiPASS L60 Скачать руководство пользователя страница 76

3-4

Registering Information in the MultiPASS L60

Chapter 3

Entering Numbers, Letters, and Symbols

Each numeric button has a number and a group of uppercase and
lowercase letters assigned to it. Use the chart below to determine which
number button to press for each character.

Press the

button to change between number mode, uppercase letter

mode, and lowercase letter mode.

When you are in number mode, “1” appears
on the right of the LCD display.

When you are in uppercase letter mode, “A”
appears on the right of the LCD display.

When you are in lowercase mode, “a” appears
on the right of the LCD display.

N

To enter a symbol, press

#

repeatedly until the symbol you want

appears. Press any other button or

>

>

to enter the symbol and move the

cursor to the right.

:a

:A

:1

«
...
74
75
76
77
78
...
»

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов