Canon MultiPASS L60 Скачать руководство пользователя страница 186

Страница: 186 / 341

7-8

Receiving Faxes

Chapter 7

Press

START/COPY

Press

START/COPY

again, then use the numeric buttons to enter a

time between 10 and 60 seconds.

❏

This setting determines how many seconds the unit rings while
waiting for someone to pick up the handset.

❏

The factory default setting is 22 seconds.

Press

START/COPY

10. Press

START/COPY

again, then use

to select RECEIVE or

DISCONNECT.

❏

This setting tells the unit what to do if no one picks up the
handset within the specified ring time set in step 8.

❏

Select RECEIVE to receive the call, and DISCONNECT to
disconnect the call.

11. Press

START/COPY

, then press

STOP

to return to standby mode.

14:30 FaxTel

DISCONNECT

RECEIVE

F/T SW ACTION

022SEC

F/T RING TIME

Содержание MultiPASS L60






















































































































































































































































































































































Результаты поиска

Содержание MultiPASS L60

Отзывы:

Canon MultiPASS L60, Руководство пользователя, Страница: 186 / 341

Результаты поиска

Содержание MultiPASS L60

Отзывы: