Canon MultiPASS L60 Скачать руководство пользователя страница 219 | Manualshive

Страница: 219 / 341

Canon MultiPASS L60 Скачать руководство пользователя страница 219

Chapter 10

Reports and Lists

10-7

Repor

ts and Lists

Memory Clear Report

If you experience a power failure, all documents stored in memory will
be lost. As soon as power is restored, the MultiPASS L60 will
automatically print a list of documents that were stored in memory
before the power failure.

N

If there are one or more documents in the image memory when the
power is cut off, the LCD will display PRINTING REPORT when the
power is restored. If there is no paper in the multi-purpose tray at this
time, the LCD will also display LOAD PAPER. If this happens, load
paper in the multi-purpose tray and wait for the unit to print the
Memory Clear Report. You will be unable to send documents or receive
faxes in memory until you do this. If you have no paper available and
you urgently need to send a document or receive a fax in memory, press
the

STOP

button to enable sending and receiving. However, please note

that once you have pressed the

STOP

button, the unit will no longer

print the Memory Clear Report.

«
...
217
218
219
220
221
...
»

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов