Canon MultiPASS L60 Скачать руководство пользователя страница 156

Страница: 156 / 341

6-28

Sending Faxes

Chapter 6

Setting Up Automatic Redialling

You can set up the following options for automatic redialling:

❏

The number of times the MultiPASS L60 attempts redialling

❏

The time interval between redialling attempts

❏

How the unit handles redialling when a transmission error occurs

❏

The factory default settings for the auto redial feature are:
•

The MultiPASS L60 redials twice.

•

The MultiPASS L60 waits two minutes before redialling.*

•

If an error occurs during transmission, the MultiPASS L60
resends the first page of the document and the pages from
where the error occurred.

❏

You can also set the redialling options from the MultiPASS Desktop
Manager. Refer to the MultiPASS Desktop Manager

User’s Guide

for

details.

Follow the procedure below to adjust the automatic redialling settings.

Press

FUNCTION

Press

to select TX SETTINGS.

Press

START/COPY

, then press

to select AUTO REDIAL.

4. Press

START/COPY

, then use

to select ON

❏

The default setting is ON.

*One minute for New Zealand

AUTO REDIAL

TX SETTINGS

FUNCTION

Содержание MultiPASS L60






















































































































































































































































































































































Результаты поиска

Содержание MultiPASS L60

Отзывы:

Canon MultiPASS L60, Руководство пользователя, Страница: 156 / 341

Результаты поиска

Содержание MultiPASS L60

Отзывы: