Canon MultiPASS L60 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 341

Canon MultiPASS L60 Скачать руководство пользователя страница 50

2-18

Setting Up Your MultiPASS L60

Chapter 2

Connecting the Power Cord

C

Follow these guidelines when connecting your MultiPASS L60 to a
power source:

❏

The MultiPASS L60 is intended for domestic use only and requires
200–240 V AC. Do not use it outside the country where it was
purchased.

❏

Use only the power cord that came with the unit. Using a longer
cord or extension cord can cause the MultiPASS L60 to malfunction.

❏

Unplug the unit only by pulling on the plug itself. Never pull on the
cord.

❏

Do not plug the MultiPASS L60 into an outlet shared with an
appliance such as an air conditioner, computer, electric typewriter,
or copier. These devices generate electrical noise, which can
interfere with the operation of the MultiPASS L60.

❏

Make sure nothing is laying on the power cord, and that the cord
cannot be walked on or tripped over.

❏

Do not overload the electrical outlet. Make sure the total amperage
used by all the machines plugged into the outlet does not exceed the
ampere rating of the outlet’s circuit breaker.

❏

Do not plug the unit into an uninterruptible power supply (UPS).

Connect the power cord as follows:

1.

Plug the supplied power cord into the power connector on the back
of the MultiPASS L60.

«
...
48
49
50
51
52
...
»

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов