manualshive.com logo in svg

Canon MultiPASS L60, Руководство пользователя, Страница: 150 / 341

Поделиться
Скачать
Canon MultiPASS L60 Скачать руководство пользователя страница 150

6-22

Sending Faxes

Chapter 6

Adding Pages to the Document in the
Automatic Document Feeder (ADF)

The MultiPASS L60 Automatic Document Feeder (ADF) can hold up to
20 A4, 20 letter, or 10 legal-size pages at a time when the document feed
lever is set to automatic document feed. If your document has more
pages than this, you can add pages while the MultiPASS L60 is
scanning.

1.

Wait until the last sheet in the Automatic Document Feeder (ADF)
starts feeding.

2.

Load up to 20 additional sheets (10 legal size). 

❑

Insert the first new page so that it overlaps the last page by
about 2.5 cm.

N

Wait until all pages of your document have been scanned completely
before starting a new job.

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов