Canon MultiPASS L60 Скачать руководство пользователя страница 189 | Manualshive

Страница: 189 / 341

Canon MultiPASS L60 Скачать руководство пользователя страница 189

Chapter 7

Receiving Faxes

7-11

Receiving Faxes

Receiving Faxes Automatically: FAX ONLY MODE

When the MultiPASS L60 is set up for a dedicated line, set FAX ONLY
MODE to automatically receive documents whenever a call comes over
the fax line.

1.

Make sure the MultiPASS L60 is set up to receive over a dedicated
fax line.

2.

Press

RECEIVE MODE

to select FAX ONLY MODE.

❏

The MultiPASS L60 assumes all incoming calls are from fax
machines sending documents. It receives the documents
automatically and disconnects all voice calls.

❏

In FAX ONLY MODE, you can control whether or not the
MultiPASS L60 rings when it receives a fax call. To set this
option from the MultiPASS L60 operation panel, refer to pages
13-10 and 13-11 (INCOMING RING setting). You can also set
this option from the MultiPASS Desktop Manager. See the
MultiPASS Desktop Manager

User’s Guide

for details. Please

note that even if you enable this option, the MultiPASS L60 will
only ring if you have the optional handset connected to it.

FAX ONLY MODE

«
...
187
188
189
190
191
...
»

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов