Canon MultiPASS L60 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 341

Canon MultiPASS L60 Скачать руководство пользователя страница 141

Chapter 6

Sending Faxes

6-13

Sending Faxes

Setting the Resolution and Contrast

Setting the Scanning Resolution

Canon’s Ultra High Quality (UHQ

™

) imaging technology enables you to

send faxes with a print quality that is very close to that of the original
document. The MultiPASS L60 also lets you adjust the resolution it uses
in sending faxes to best suit your particular document.

The MultiPASS L60 has three resolution settings:

❏

STANDARD

resolution (203

×

98 dpi) is adequate for most text

documents.

❏

FINE

resolution (203

×

196 dpi) is suitable for documents with fine

print (smaller than the print in this sentence).

❏

PHOTO

resolution (203

×

196 dpi, with halftones) is for documents

that contain photographs. With this setting, areas of the document
that contain photos are automatically scanned with 64 levels of grey,
rather than just two (black and white). This gives a much better
reproduction of the photos, though transmission time is longer.

Set the resolution as follows:

1.

Press

RESOLUTION

.

❑

The LCD display shows the current resolution setting.

2.

Press

RESOLUTION

until the resolution you want is displayed.

(FINE resolution with halftone)

3.

Continue with the operation you wish to complete.

❑

If you do not proceed with any other operation, the LCD
display returns to standby mode after about 5 seconds.

14:30 FaxOnly

STANDARD

PHOTO

FINE

STANDARD

«
...
139
140
141
142
143
...
»

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов