manualshive.com logo in svg

Canon MultiPASS L60, Руководство пользователя, Страница: 295 / 341

Поделиться
Скачать
Canon MultiPASS L60 Скачать руководство пользователя страница 295

Appendix A

Specifications

A-5

Specifications

Recording method:

Laser Beam printing

Recording paper sizes:

• A4 (210 

×

297 mm)

• Letter (8.5 

×

11 in.)

• Legal (8.5 

×

14 in.)

Recording paper weight:

64–90 g/m

2

Fax printing speed:

Approx. 6 pages/minute*

Dialling:

• Automatic dialling:

– One-touch speed dialling (16 locations) 
– Coded speed dialling (100 locations)
– Group dialling (115 locations)

• Regular 10-button dialling 

(with numeric buttons)

• Automatic redialling (including error 

redialling)

• Manual redialling
• Pause button

Networking: 

• Delayed transmission (up to 117 locations 

at a single pre-set time)

• Sequential broadcast (up to 117 locations)
• Automatic receiving
• Non-ring reception
• Deactivate ECM
• Net. Switch (Australia and New Zealand

only)

Report/reference:

• Activity report (up to 20 transactions)
• Non-delivery report
• TTI (Transmitter Terminal Identification)

Toner saver:

Economy mode for printing received faxes
approximately doubles the cartridge life.

* Based on Canon FAX Standard Chart No. 1, A4, standard mode.

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов