manualshive.com logo in svg

Canon MultiPASS L60, Руководство пользователя, Страница: 31 / 341

Поделиться
Скачать
Canon MultiPASS L60 Скачать руководство пользователя страница 31

Introducing the

MultiPASS L60

Chapter 1

Introducing the MultiPASS L60

1-17

C

Unplug the MultiPASS L60 and contact your local authorised Canon
dealer or the Canon help line in any of these situations:

❏

If the power cord or plug is damaged or frayed.

❏

If liquid spills into the unit, or if it is otherwise exposed to rain or
liquids.

❏

If you notice smoke or unusual noises or odour coming from it.

❏

If the MultiPASS L60 does not operate normally when you follow
the operating instructions. Adjust only those controls that are
covered by the operating instructions in this user’s guide, or you can
damage the unit and require extensive repair work.

❏

If the MultiPASS L60 is dropped or its cabinet damaged.

❏

If the MultiPASS L60 begins performing poorly, and you cannot
correct the problem by following the procedures in Chapter 11,
“Frequently Asked Questions”.

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов