Canon MultiPASS L60 Скачать руководство пользователя страница 134 | Manualshive

Страница: 134 / 341

Canon MultiPASS L60 Скачать руководство пользователя страница 134

6-6

Sending Faxes

Chapter 6

Selecting Automatic/Manual Document Feed

With the MultiPASS L60, you can select whether you want to scan
documents automatically or manually.

Automatic document feed is used when scanning multipage documents
on normal paper. Use manual document feed when scanning single-
page documents such as photos, business cards, or documents on other
special types of paper. Manual document feed will allow you to scan
your document with minimum damage to the surface of the document.

N

When using manual feed, use a carrier sheet to avoid scratching the
surface of important documents (photographs, for example).

Use the document feed lever located at the top of the operation panel, to
select automatic document feed or manual document feed.

Automatic document feed

Manual document feed

«
...
132
133
134
135
136
...
»

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов