Canon MultiPASS L60 Скачать руководство пользователя страница 161 | Manualshive

Страница: 161 / 341

Canon MultiPASS L60 Скачать руководство пользователя страница 161

Chapter 6

Sending Faxes

6-33

Sending Faxes

N

If the MultiPASS L60 memory becomes full while scanning your
document, MEMORY FULL appears in the LCD display. If this happens,
remove the remainder of the document from the Automatic Document
Feeder (ADF). You may need to open the operation panel to do so. See
page 6-24 for details. Then divide the document into several sections
and send each section individually.

Sending a Document Using Group Dialling

If you frequently send faxes to the same group of people, you can create
a “group.” Groups are stored under one-touch speed dialling buttons or
coded speed dialling codes. See Chapter 5, “Speed Dialling” for details
on registering numbers under groups and using group dialling.

«
...
159
160
161
162
163
...
»

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов