Canon MultiPASS L60 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 341

Canon MultiPASS L60 Скачать руководство пользователя страница 2

ii

Preface

(Europe only)

Copyright

Copyright © 1998 by Canon, Inc. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language
in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual, or otherwise, without the prior written permission of
Canon, Inc.

Although this equipment can use either loop disconnect or DTMF
signalling, only the performance of the DTMF signalling is subject to
regulatory requirements for correct operation. It is therefore strongly
recommended that the equipment is set to use DTMF signalling for
access to public or private emergency services. DTMF signalling also
provides faster call set up.

This CE Marking shows compliance of this equipment with Directive
73/23/EEC and Directive 89/336/EEC (as amended by Directive
92/31/EEC), both as amended by Directive 93/68/EEC.

Canon Inc. /Canon Europa N.V.

«
1
2
3
4
...
»

Содержание MultiPASS L60






















































































































































































































































































































































Отзывы:

Нет отзывов